Introduction:Few gaming accessories are as important as a gaming headset. Not only do they let you communicate with other players, but they also provide an immersive audio experience that can take your gaming to the next level. Unfortunately, most headsets come with one major downside: cords. Cords can be a major inconvenience, and they often get in the way during gameplay. But don’t worry – we’re here to help. In this article, we’ll show you how to fix the cord on a gaming headset. KEY TAKEAWAYS Step 1: Do not try to fix the wire while it is plugged into anything. This will likely cause damage to the wires and could potentially be dangerous. Step 2: Cut the wire about 4 inches from the plug using wire strippers. Be sure to remove all of the insulation, exposing the individual wires. Step 3: Take the replacement headset plug and thread each wire through its respective lead. Step 4: Twist each wire around its corresponding screw on the plug, making sure they are tight. You can use a lighter to tighten them further, but be careful not to burn the insulation. Step 5: Plug in your fan and place it so that the air is blowing on the plug. This will help to dry it and prevent any short circuits. Step 6: Apply a small amount of glue to each wire where it meets the plug using a glue gun. Let it dry completely before using your headset again. How to Repair Gaming Headset Detachable Cables Detachable cables are a gaming headset’s best friend. They make it easy to wrap and store your headset, they keep the weight of the headset down, and they make it easy to repair when something goes wrong. Unfortunately, things do go wrong and cables can eventually wear out or come loose. If your gaming headset has a detachable cable, follow these instructions to easily fix the cable plug’s issue. Insider Tip Fixing a headset with a damaged cord can be a pain, but with a little patience and these simple steps, you can do it yourself. The most important thing to remember is to keep the wires separated as you work, so you don't have to deal with tangles later on. If you're having trouble getting the wires apart, use a pair of scissors to cut through the insulation and then strip the wires back. Always unplug any electronics before repairing them to protect yourself and others. This method can potentially fix static, one side of the headset not working, and sound that cuts out. STEP 1 STEP 1: Cut the cord about 7 cm from the start of the audio jack. To do so, you will need a utility knife or another sharp object to cut the rubber insulation around the wires and the wires themselves. Be very careful not to cut into the copper wiring inside. If you have a frayed portion of the internal wire, cut just above the fray to repair this area. STEP 2 STEP 2: Burn off the enamel coating on the wire. This is the most straightforward way to remove the coating, and it also decreases the chance of damaging the cable beyond repair. If you choose to use a pair of wire cutters, ensure you don’t cut into the wire within the coating. STEP 3 STEP 3: Strip the insulation from the end of each wire. This is easiest if you strip them all down to the same length, but it's not mandatory. You'll want to have about ¼" of wire exposed on each end. Be careful not to cut the wires themselves! Once you have the insulation stripped, twist together the two ground wires. You should see four wires: two gold or copper grounds, one red right channel, and one blue or green left channel wire. The ground wires can be wound together by twisting, but the other two should stay separate. Pull them off to either side to make the process easier. STEP 4 STEP 4: Once you have the housing unscrewed, you'll be able to see the wire coming out of it. Slip the wire through the hole in the housing, then screw the housing back onto the protruding part of the product. Make sure it's tight, so it doesn't loosen over time and create sound issues. STEP 5 STEP 5: Apply a small amount of solder to the end of each wire, making sure that the ground wires are held together. Just a dab of solder should work fine for this process. You just want to make sure that it sticks. STEP 6: Carefully reattach the cover and screw it into place. Try not to over-tighten it, as this could damage the headset. STEP 6 STEP 6: Now, it's time to reattach the cables to the connector. Take the ground wire and wrap it around the middle hole on the connector. Make sure the cord is securely in place, then do the same with the left and right cables. The green or blue wire goes in the left hole, and the red wire goes in the right. Make sure everything is in place before moving on to STEP 7. STEP 7 Now that your cord is cut, it's time to solder it back together. Strip the insulation off of each lead and twist them together like you would a wire. Then, use your soldering iron to apply solder to each lead, covering the hole and wire completely. To avoid the cables touching, you can use hot glue between the leads to secure them. Hold the iron on each solder joint for about 10 seconds or until the solder has melted. Let cool and enjoy your repaired headset! STEP 8 Remove any extra wires to make it easier to screw the cap on top of the headphone plug. If your cable has a compression element, this step is less important, and you can squish them down. Conclusion:If you're a gamer, there's a good chance you've experienced the frustration of a broken or damaged gaming headset cable. Whether the cord is too short, the connector is loose, or the wires are exposed, a damaged headset cable can make it impossible to enjoy your favorite games. In this post, we'll show you how to fix the cord on a gaming headset using two simple methods. With a little patience and some basic tools, you can have your headset up and running like new in no time.
0 Comments
Leave a Reply. |
AuthorDon’t buy anything until you’ve read a review. Our expert reviews are the best way to know without a doubt that you are getting the right product for your needs. We only review products we think are worth. Archives
May 2022
Categories
All
|
Recommendations are independently chosen by Gadgets & Gifts editors. Purchases you make through our links may earn us a commission.